Glass doors are not uncommon in daily life. How are glass doors installed? Today, the editor will introduce the specific steps of installing glass doors.
Glass door is a kind of special door leaf. First of all, its thickness is not enough to be a solid door, but it does not belong to special-shaped door. In fact, it is a kind of special door leaf. Glass doors are divided into tempered glass and ordinary float glass. Generally, glass materials with a thickness of 12mm (mm) are used. Tempered glass is used to be firm.
, and safe. Glass doors are not uncommon in daily life. How are glass doors installed? Today, the editor will introduce the specific steps of installing glass doors.
How to install glass door?
1. Positioning and pay-off
fixed glass and movable glass door leaf combination glass door, unified pay-off positioning, according to the design and construction drawings requirements, release the glass door positioning line, and determine the door frame position.
2. Install the glass door frame top limit slot
the width of the limit groove should be two to four millimeters greater than the thickness of the glass, and the depth of the groove should be ten to twenty millimeters. During installation, at the beginning, two metal decorative board edges are led out by the bullet line, then the top limit groove of the door frame is installed according to the edge line, and the groove depth in the groove is adjusted through the glued backing plate.
3. Install glass door-wood base support with metal finish
fix the square wood on the ground and stick the metal all-purpose adhesive on the wood with trim board. If aluminum alloy square tube is used, it can be fixed on the frame column with aluminum angle, or fixed on the wooden brick buried in the ground with wood screw.
4. Install vertical door frame
the bullet center line is connected to nail the square wood of the door frame, then use plywood to determine the shape and position of the door frame column, and finally the metal decorative surface is outsourced. When wrapping up the finish, put the opposite joint position of the finish on the middle door position on both sides of the glass installation.
5. Install glass door glass
use glass suction tray machine to suck the thick glass tightly and lift the thick glass plate to the installation position. First insert the upper part of the glass into the limit groove at the top of the door frame, and then put the lower part of the glass on the base support.
6. Fixed glass
the inside and outside nails on base support square wood two small square wooden strips clamp thick glass on the middle door, paint all-purpose adhesive on the square wood strips and stick the decorative metal on the square wood strips.
7. Note silicon sealant sealing
on both sides of the top limit groove and the bottom bracket ports, as well as the gaps between the thick glass and the frame column, inject silicon sealant to seal, and scrape off the excess silicon sealant with tools.
8. Glass docking
when the fixed part of the glass door needs to be spliced due to over dimension, its butt seam should have a width of two to three millimeters, and the edge of the glass plate should be chamfered.
9. Install the floor Spring of the glass door
before installing the door leaf, the positioning pin on the ground floor spring and the top surface of the door frame should be installed and must be coaxial line. It is best to check with hanging line to ensure that it is in the same straight line during installation.
10. Install glass door up and down door holder
install the upper and lower metal door holder on the upper and lower ends of the glass door leaf respectively. If the height of the door leaf is not enough, door holder plywood strips can be placed at the bottom of the glass in the Lower Wood (en) pallet.
11. Fixed glass door door holder
after the height of the door leaf is fixed, insert door holder into the gap between the glass and the two sides of the upper and lower small Batten, and inject silicon sealant into the gap for fixing.
12. Install glass door leaf
first, adjust the positioning pin with its own adjusting screw to pull out the beam plane 2mm, and stand up the office glass door leaf. The hole position of the rotating pin connector within door holder under the door leaf is aligned with floor Spring of rotary pin shaft, turn the door leaf to put the hole position on the pin shaft, turn the door leaf to a right angle with the door frame beam, align the rotating connector hole in door holder on the door leaf with the positioning pin on the door frame beam, adjust the adjusting screw of the positioning pin, insert the locating pin into the hole.
13. Install glass door handle
before installation, apply a little silicon sealant on the part where the handle is inserted into the glass. When the handle is assembled, the root is close to the glass and then the screws are fixed tamp down to ensure that the handle is not loose.
How is the glass door installed? I believe everyone will introduce it to you after reading today's editor. The specific steps for installing the glass door should be understood, for more products of doors and windows and related knowledge, please continue to pay attention to Zhonghua door and window network.
(Article Source: Hongyao engineering glass WeChat, invasion and deletion)
