Casement window how to install car window shade casement window with car window shade common ones include Diamond net and invisible car window shade. Let's take a look at how to install car window shade. 1. Aluminum alloy casement window with Diamond net is the same as installing aluminum alloy doors and windows. Aluminum alloy outwards opening window is a casement, while the attached Diamond net becomes two casement.
Casement window how to install car window shade
casement window with car window shade common ones include Diamond net and invisible car window shade. Let's take a look at how the two are installed with car window shade.
1. Aluminum alloy casement window with Diamond net
like installing aluminum alloy doors and windows, aluminum alloy outwards opening window is a casement, while the attached Diamond net becomes two casement. There are two lines up, down, left and right of the door frame. The activity opening of aluminum alloy outwards opening window is mainly wind brace up and down, while Diamond net is hinge to move.
Diamond mesh
① install diamond net
when the auxiliary frame and Wall are connected and fixed, the outer fan is also installed. According to the previously adjusted Diamond net fans, measure the distance between the upper and lower ends of the Diamond net fans (the point has been taken and the hinge has been adjusted), and then take the same distance between two points on the right side of the inner sub-frame, note that the size distance is the same as that of diamond net fans. Then use electric drilling to take Holes. The hinge is usually three or four holes. Install the hinge at the upper and lower ends, and install diamond net fans at the other end of the hinge. Usually professional door and window manufacturers will adjust the whole door and window in advance, and directly connect it with bolts according to the holes drilled.
Installed casement window with diamond mesh
2. Casement window with invisible car window shade
invisible car window shade is voile that can automatically roll back car window shade, mainly used for ventilation and mosquito prevention. The frame is tightly attached to the window frame. When you need it, pull the voile down. When you don't need it, the voile will be automatically rolled back to the net box.
Invisible car window shade picture
① tools used
structural Adhesive, glue gun, double-sided adhesive, cloth
② invisible car window shade Assembly
1) open the invisible car window shade package and check the invisible car window shade quantity of accessories, and tile the invisible car window shade on the desktop
2) tear open the double-sided adhesive film and stick the double-sided adhesive tape on the place where the distance between the double-sided adhesive tape is relatively large.
3) make structural adhesive with a diameter of 3mm in the neutral part without double-sided adhesive tape
4) fix reel on the window frame
5) fix the left and right sliding rails on the window frame,
6) fix bottom slide rail on the window frame
8) adjust car window shade damping deceleration device
note: when adjusting the damping of car window shade, you should debug and pull car window shade up and down.
3. Install invisible car window shade
1) put car window shade on the installation part, pay attention to the left and right air groove and the margin of the door and window frame should be symmetrical left and right, the bottom position should be about 5cm lower than the frame of the door and window frame, after putting it, use clips to hold the left and right sides, make it impossible to move.
2) use an electric drill with a 3.2mm drill bit to punch holes at the inside leather strap of the door and window frame.
3) put 6 to 14 Eyes on the corresponding parts of the left and right air ducts and the bottom of the bottom as needed, and then screw the screws to complete the installation.
4. Precautions
1) the yarn box should be fixed vertically, and the two ends should be evenly occupied by the upper and lower borders.
2) the upper and lower slideways are fixed in parallel with the position of the yarn box to avoid deviation inside and outside the slideways.
3) the position of the base should be close to the pull beam, and the sliding window fans placed should be closed tightly before drawing lines and fixing them, so as to avoid the fixed position being too close or too far.
If the fixed studs of each part is too long, the normal sliding of sliding window fans will be prevented, and the self-powered nails can be cut short with cutting pliers.
