The construction acceptance of wooden doors and windows introduced today is very helpful for the installation and acceptance of wooden doors and windows. No matter what acceptance is, let's take a look at the matters needing attention in the construction acceptance of wooden doors and windows.
First of all, tap the side panel of window and door sets by hand. If Air Force Drum Corps sound is made, it means that there is no base plate such as thin wood board on the bottom layer, which should be removed and redone.
1. Make curtain boxes according to the requirements of rooms and drawings. If curtain rods are directly installed without curtain boxes, pay attention to the opening distance of window frames and the thickness and length of curtain rods when installing curtain rods.
2. When making panel curtain boxes, first make a 7-shaped frame nail on the top, and Seal both sides with wood board. A 20*18mm wood strip is used to reinforce and fasten the lower mouth of the vertical frame to prevent deformation. For example, if the water seal nail is trim board, the surface of the base layer must be smooth and clean if the water mixing paint is done.
3. When making window frame with thin wood board or density plate, fix the basal plate on the base keel of the window frame first, and then nail the lines and zigzag nails to prevent the lines from curling, and the included angle should be dense and flat, marble is suitable for the lower mouth of window frame to avoid blackening and deformation due to moisture.
4. Door set after the frame is made of wood, it should be planed flat and straight, and then installed on the wall after assembly molding, covering basal plate and trim board.
5. Appearance should be beautiful: the surface paint film of wooden doors and windows should be smooth and bright, without quality defects such as falling, bubbles, wrinkles, etc., without corrosion points, sound knot, and broken; the wood used in package window and door sets should be coordinated with the wood and color of doors and windows. The color difference between trim board and Wood lines should not be large, and the tree species should be the same.
6. The door casement should be square and cannot be warped and deformed. The door casement can just be inserted into the door and window frame, which is consistent with the door and window frame: if the gap between the door casement and the frame is large, it is mainly because the planing is not correct during installation or the door and window frame are not perpendicular to the ground. You can remove the door casement and re-planing; If the door and window frame is not vertical, the gasket in the frame plate should be straight.
7. The hinge should be located accurately and installed firmly: If the hinge is not straight, the door and window fan will not match the frame cover and the door and window switch will not be smooth. You can twist a screw on each hinge first, then adjust the consistency between the door and window fan and the frame, adjust the repair and then tighten all the screws. If the hinge screw is short, or the hinge screw is nailed in at screw tightening, the screw is not twisted, or the screw is inclined, it will cause the door and window fan to go around. The appropriate screws should be replaced. The screws must be straight when they are put on. The screws should be nailed in 1/3 first, and the rest should be screwed in.
8. The door lock should be opened and locked smoothly. The two parts locked on the door leaf and the door frame should be consistent: if the lock is not properly installed, the door leaf will not switch freely. Remove the bolt plate, repair the tongue groove with chisel, adjust the position of the bolt mouth of the door frame, and then install it. In addition, the opening direction of the door should also meet the requirements.
9. There should be base material inside the door and window cover: window frame when it is made of fine wood board or density plate, the basal plate should be fixed on the base keel of the window frame first, and then the lines should be nailed; Door set it is appropriate to use wood to make the frame, planing, planing straight, then assembling and molding installation on the wall, and then covering basal plate and trim board. Tap the window and door sets side panel by hand. If a Air Force Drum Corps sound is made, it means that the bottom layer does not have base plate such as thin wood board, which should be removed and redone.
10, door set should be vertical, trim board paste flat, Angle Square, no big and small head, trumpet phenomenon exists.
