Wooden doors occupy a very heavy position in our home decoration, and they should be installed with great care. So do you know the installation steps of wooden doors? Do you know the installation standards of wooden doors?
Wooden door installation procedure and wooden door installation standard
1 Preparation phase
Don't underestimate this stage. If you don't do it well, there is no way to install your wooden door. We should customize wooden doors according to the actual situation before, unpack them after arrival, and confirm that all parts are complete (especially hardware accessories). After that, prepare hammers, rulers, ropes, connectors, special firmware, etc., and clean the ground to confirm whether the corners of the door hole have been polished and smooth.
2 Construction phase
First, we need to assemble door set. In the previous wooden door installation step, we have sorted out the parts of the wooden door, so at this time, we only need to join the door set and riser according to the number. Next, install door set in the entrance hole. This is an important installation procedure for wooden doors. We should first fix the four sides of door set and pay attention to whether door set is perpendicular to the ground. At this time, the installation standard of wooden doors is that the vertical error cannot exceed 2mm, the horizontal error cannot exceed 1mm. Then the door leaf is installed, and the sealing strip must be done well. Finally, hardware installation, including door locks, hinges, door shutters, etc., must ensure flexibility and firmness.
3 Acceptance phase
After the wooden door is installed, everyone should pay attention to the acceptance, which is also one of the wooden door installation steps. At this time, the installation standard of wooden doors is that the joint seam between door line and the ground should not exceed 3mm, while the door locks should be flexible, the connectors should be firm and tight, and the overall decoration effect of wooden doors should be good.
Wooden door installation is easy to make mistakes, please pay attention!
Fashion eco-door
Precautions for wooden door installation
(1) when installing wooden doors, you must reserve holes, instead of cooking by installing and opening, because this will make the error when installing wooden doors very large.
(2) pay attention to the drying degree of the wall when installing wooden doors. If the wall is too wet (moderately more than 25%), it cannot be constructed rashly. We should take moisture-proof measures on the wall, such as making an isolation layer.
Wooden door installation is easy to make mistakes, please pay attention!
Fashion eco-door
Wooden door installation error-prone details
When carrying solid wood door panels, try to avoid scratching or hurting the door frame and door leaf. When placing the door frame and door leaf, it should also be placed on the indoor horizontal ground without direct sunlight but air circulation. Remember to place the door frame and door leaf diagonally, which is easy to damage the door frame and door leaf.
The wooden door must be installed in the floor project (such as floor tiles and stone) at the entrance, and after the putty on the wall is scraped and polished, (the wall needs to be wall tile, the hole at the stone, the installation steps of the wooden door can only be carried out after all the sides of the opening are attached.
The installation method of wooden door must use the reserved hole installation method, and it is strictly prohibited to use the method of side installation and side opening.
Wooden door installation is easy to make mistakes, please pay attention!
Wooden door installation effect diagram
When installing wooden doors, you need to check the humidity of the wall at the opening. If the humidity of the wall at the opening is less than 25%, you can continue to install it normally. If the humidity of the wall at the opening is more than 25%, then the moisture-proof isolation layer should be made on the installed wall.
If a wooden door is installed at the corner wall or T-shaped wall, a "fake wall" with a size of not less than 50mm should be made on the side of the gate stack without plane width before installation ". Of course, the width of the false wall here can be determined according to the width of the line to avoid the asymmetry of the edge lines displayed on both sides.
If the door frame is made of MDF material, screws should be used when assembling the door frame; If the door frame is made of multi-layer board or solid wood boards, iron nails can be used to fix the door frame.
When installing the door frame, you must adjust the verticality of the door frame to avoid damaging the door frame due to the drying and swelling effect of the foaming agent.
Because the two sides of the door frame may be powered by wired lines, the electricity operation must be standardized when installing the door frame.
Confirm the ground forming height and wall thickness according to the decoration baseline when measuring the Mao cave opening.
The reserved size of single vertical hinged door, sub-mother door and double double-door door opening is (the thickness of motherboard is 32mm): the height of the door opening = the height of the door leaf + 40mm, and the width of the door opening = the width of the door leaf + 65mm. Other types of combined doors are determined according to the specific situation (note: the height of the door opening refers to the net height, width and thickness of the door opening, which are also the net size from the ground engineering of the opening).
Editor: China Door Industry Network-dog thief
