Decoration can be said to be a university question. From the early design-mid-term construction-late acceptance, the patience and professionalism of the owners are tested one by one. After the decoration of my house, I am a half expert. Today, let's talk about the precautions for the installation of inner door. Let's look down together!
(The article comes from the Internet and is invaded and deleted)
inner door installation is not difficult, but there are still some details to be grasped. How to install inner door? What should I pay attention to when installing inner door?
Inner door does not mean that you can install it as you want, and the following conditions must be met when installing inner door!
1. The installation method of reserved holes must be adopted for installation inner door. It is strictly prohibited to install the side opening;
2. Installation inner door must be installed on the floor project (floor tile or stone) at the door. It is recommended to install the project after the Wall operation is completed.
It is not enough to meet the above conditions. If you want to install inner door smoothly, you must do the following checks:
1. Check whether inner door products are damaged;
2. Measure whether the size of the opening is consistent with the product to be installed;
3. Check whether the opening is regular and whether the wall is firm.
If you have met all the above conditions, congratulations, you are qualified to install inner door! Hurry up and get the tools ready to start! But what tools should be prepared? See clearly, don't miss it. Electric Hammer, electric drill, woodworking hammer, planing, fine tooth saw (hacksaw), screwdriver, Angle Square, tape measure, plumb bob, Tapper, chisel, the installation tools of the corresponding specifications must be prepared. There are also inner door installation materials: iron nails, self-tapping screws, 502 glue, all-purpose adhesive, wood screw (40?, 25?), Small Batten, Styrofoam, white latex, door lock, hinge, door stopper, etc. should also be checked clearly.
(The image is from the Internet and deleted)
then start installing! Inner door installation steps are as follows:
1. First check whether the parts of the door leaf are complete, whether the sizes of the parts are correct, and whether the corresponding installation position of each set of doors is consistent with the size of the door opening.
2. The fixed door frame uses one side of the door hinge as the reference edge and the upper reinforcement of the reference edge as the reference point. Fix the reinforcement of the base point on the wall with large cement nails or explosive screws to ensure that the whole door frame is vertical and then fix the lower two rows of reinforcement.
3. Fix the whole door frame with the bolt of the door leaf on one side of the door lock to align the keyhole of the door frame, adjust the position, and then fix the three rows of reinforcing ribs on the wall one after another under the condition of ensuring vertical. The installation of stainless steel anti-theft door can combine the steps of "one" and "three" into one step and fix it directly with explosive screws.
4. Debug and try to open and close the door to see if it is smooth and the position of the door lock is accurate. It is easy to open and close. If there is a problem, it can still be adjusted in a small range, and the position can be adjusted to the ideal level all the time.
5. Pour cement to ensure the accurate position of the whole door. After the switch is smooth, you can use impact drill to open small holes in the upper and middle sections of the door frames on both sides, from these holes to the frame, cement is poured into the left, right and upper door frames, so that the door frame is not only closely connected with the wall, but also makes the door frame itself extremely hard. (The installation of stainless steel gate can omit this step depending on the specific situation)
6. After the whole door is installed on the modified wall, the cement will smooth the wall around the door frame, and then the surface can be equipped with paint consistent with the surrounding whole,
after understanding the installation steps, in order to make your installation process more smooth, the following inner door installation precautions should also be well understood.
1. Inner door paint is afraid of bumping, so pay attention to impact protection.
2. Hinge. The lock is an movable accessory. When it is loose, it should be tightened immediately. If the hinge position is noisy, it should be filled with oil in time. If the lock is not flexible, add a proper amount of pencil leads to the keyhole, do not fill oil casually.
3. In terms of cleaning, organic solvent cannot be used for scrubbing, and organic solvent will damage the paint layer on the surface. When painting the wall, cover the inner door so as not to drop the paint on the surface of the product, peel off the finishing material, fade, and affect the overall appearance. Inner door is the solid wood skin, which is very inflammable.
4. Inner door are afraid of water. If it is really soaked by water, it is generally very troublesome. However, for the moisture-proof problem, inner door of the finished products are doing well at present. Pay attention to the kitchen and bathroom, and do not accumulate water, especially the bottom of door set.
5. The heating problem in winter, the indoor should not be too dry, and the humidity in the air should be kept at about 40%, which is the best for the floor, inner door, and even the home.
I believe you have read the above introduction. The installation procedure of inner door is very clear. The installation of inner door looks simple. Just install the door, but in fact, you need to pay attention to many details, sizes and other issues. All these have a lot to do with the smooth use in the later period. Now merchants who buy wooden doors will pack the installation, so you don't need to worry about it. After the installation and acceptance, you can do it! Have you got today's little knowledge?
