However, the installation is not a real thing, so it is difficult to see it as a reality, and human factors have a great influence. Therefore, it is very difficult for consumers to inspect "the installation of this merchant is unreliable" when purchasing door and window products.
In view of this, Xiaozhi will open a new "door and window installation" topic in the near future, which will be used for "science popularization" home decoration door and window installation process, auxiliary materials accessories, key points of investigation, attention to details, etc.
01 is the installation position of windows also exquisite?
Of course.
The width and size of doors and windows of home decoration are different. The narrow window sill is only 10cm, and the width can reach 30cm or more. The size selection of doors and windows series is also different, from 60 series (6cm) there are more than 100, so there is a large choice for the installation position of the window.
At the same time, the installation of doors and windows should consider factors such as safety, practicality, performance, beauty, etc. Xiao Zhi listed some common situations related to the installation location of windows below.
02 must abide by the principle: the installation of Windows shall not exceed the drip line
the installation position of the window must first take into account the rain floating in the Casement opening condition.
That is, the installation position of the window cannot exceed that above the eaves. Drip line, if there is no drip line in the eaves where the window is installed, it can be installed within a few centimeters to prevent the "mid-range" oblique wind and rain level from dropping onto the window frame or floating directly into the room.
In particular, outwards opening window windows (open outward) should be paid special attention. If you want to forget to open the window without fear of "mid-range rain", the installation position should be "when about 30 ° is opened outside" but not the drip line.
03 waterproof factors to be considered: avoid leakage caused by outside finish
when the exterior wall (outside finish) encounters decorative (functional) materials such as ceramic tile, dry hanging Stone, aluminum plate, insulation layer, etc., the installation position of the window shall be evaluated and handled.
That is to say, if the window is fixed, whether the integrity of these materials will be damaged, resulting in rain may penetrate into the room along the gaps such as tiles. Or consider whether the materials themselves have the possibility of leakage. If the outside finish is leaking, the windows will be installed on the outside finish, and there will be indoor leakage problems in the future.
Regular is generally right waterproof materials, or cut the materials to the installation position of doors and windows, and then install doors and windows after waterproofing.
△ cut the insulation layer to the installation position, glue and waterproof, and install door and window stickers insulation layer;
04 when the window sill is wide, the window can be installed as far as possible.
If the window sill is wide at home, the window can be installed in the center or as far as possible under the premise of "drip line.
Especially in the kitchen, bathroom, balcony and other locations, the extra window sill can be placed in bottles and cans, effectively utilizing the space.
05 when the window sill is narrow, the window recommend is flush against the inside, or the interior finish is flush.
The window sill is narrow, only a dozen centimeters, often appear in the old community. In addition, now the window series is relatively large, often 70 / 80 / 108(mm).
It is easy to encounter that the outside installation is easy to be exposed to rain, and the indoor window sill left in the middle (or outside installation) is very narrow, and nothing can be put in the width of two or three centimeters, so cleaning is still troublesome.
In order to avoid such chicken ribs windowsill , the installation position of the window is recommended to be installed flush inside or flush with the tile surface.(About 2cm during installation, it can be flush with tile Chamfering to avoid the trouble of tile flanging and closing).
06 ultra-high heat insulation requirements out-cell installation
when the performance level of windows in the home reaches "passive", the installation method of out-cell often enables the whole window to achieve the best thermal insulation effect.
Of course, non-passive windows can also pursue high installation standards. In terms of installation location, they can be installed in the middle or outside according to different wall structures, which also has the effect of improving performance.
Finally, the installation location of windows and the cooperation between the closing of windows and interior decoration are important manifestations of the installation and service experience and attitude of door and window merchants. When consulting merchants and door and window scheme design, consumers can ask more about the plan. The more the merchant manages for you, the better.
The above is the common installation location known by Xiao Zhi. Welcome to leave a message to correct and add ~
